Fishing with Rod Discussion Forum

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Staver River (at Ruskin dam) flows  (Read 4151 times)

fishman254

  • Full Member
  • ***
  • Offline Offline
  • Posts: 89
Staver River (at Ruskin dam) flows
« on: November 01, 2013, 09:23:59 AM »

Can find where I can get the Stave River at Ruskin Dam flows. Help! I'll be anchoring below the dam and that info would be real helpful.
Logged

Easywater

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 1007
Re: Staver River (at Ruskin dam) flows
« Reply #1 on: November 01, 2013, 03:25:58 PM »

There's no map if that's what you are looking for.

It is a relatively difficult river to navigate once you get into the upper part of the river (past the bottom island).

You should have a fishfinder to show your depth and it would be advisable to have a spotter in the front of the boat pointing you to deeper water as you move up.

After you pass under the bridge, stay to the east side of the river until you get near the pilings.
Sort of stay close to (& south of) the pilings as you move up the river.
At some point, you will need to go on the north side of the pilings otherwise you will get pushed into shallow water.

There is a very shallow spot near the top of the first island that can be impassable depending on the tide.

Speaking of tides, you have to pay careful attention to the tides and try to time your movements with high tides.

Using Google Maps or Google Earth will help you figure out where to go.
Logged

fishman254

  • Full Member
  • ***
  • Offline Offline
  • Posts: 89
Re: Staver River (at Ruskin dam) flows
« Reply #2 on: November 01, 2013, 03:48:45 PM »

Good info, Easy.
Is there some place (online or phone call) where I can, like the Harrison/Fraser, see the FLOWS or river HEIGHT (cubic meters/second, or discharge)?
« Last Edit: November 01, 2013, 03:54:12 PM by fishman254 »
Logged

Suther

  • Sr. Member
  • ****
  • Offline Offline
  • Posts: 355
Re: Staver River (at Ruskin dam) flows
« Reply #3 on: November 01, 2013, 04:15:46 PM »

Good info, Easy.
Is there some place (online or phone call) where I can, like the Harrison/Fraser, see the FLOWS or river HEIGHT (cubic meters/second, or discharge)?
I would guess probably not because flow is controlled by bc hydro, all depends on how much they let past the dam. And with construction they are keeping flows low I think
Logged

Easywater

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 1007
Re: Staver River (at Ruskin dam) flows
« Reply #4 on: November 02, 2013, 10:00:16 AM »

Stay to the right as you round the corner
Hug the shore as you move past the pilings - green line - 6 to 8 feet deep depending on the tide
Red arrow shows where you transition from s/e of the pilings to n/w of the pilings
Red square shows the main shallow spot - 2 to 3 feet deep
If you can get above that, you are in the hot zone
Toilet bowl is just off the top of the pic

There's usually a fair amount of charter boat traffic - follow them but keep in mind they are probably jets.

Logged

fishman254

  • Full Member
  • ***
  • Offline Offline
  • Posts: 89
Re: Staver River (at Ruskin dam) flows
« Reply #5 on: November 03, 2013, 07:32:53 AM »

Nice map, Easy!!
That's super helpful.
"Hot zone", by that do you mean the best fishing, or what?
Thanks!
Logged