Fishing with Rod Discussion Forum

Please login or register.

Login with username, password and session length
Advanced search  

Author Topic: Ghost shrimp pump problems  (Read 4687 times)

vancook

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 687
Ghost shrimp pump problems
« on: February 04, 2013, 06:11:41 PM »
Anyone on the board have an alvey shrimp pump?
Went out to pump bugs tonight and could not get any suction at all. I didn't use my pump last season, didn't go steelheading, but have used it frequently for the previous two seasons with no issues.
Can anyone think of a possible issue and or fix? I'm thinking maybe the rubber "washer" is worn on the sides and not allowing suction to form. If so anyone know if you can buy a replacement part?

Thanks in advance
Logged

jetboatjim

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 779
  • catching poachers.
Re: Ghost shrimp pump problems
« Reply #1 on: February 04, 2013, 06:49:42 PM »
did you try cranking down the "wing-nut " at the bottom ?

I made a new rubber washer out of a old wheel barrow tire.
Logged

vancook

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 687
Re: Ghost shrimp pump problems
« Reply #2 on: February 04, 2013, 07:02:24 PM »
I did. Cranked it as much as I could. Still wasn't getting suction.
Going to fiddle around with it at home.
Will keep a look out for spare rubber pieces
Logged

chris gadsden

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 13952
Re: Ghost shrimp pump problems
« Reply #3 on: February 04, 2013, 08:09:00 PM »

Rubber washer most likely dried out, soak in some water for a few hours and see if that helps.
Logged

Fish Assassin

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 10839
Re: Ghost shrimp pump problems
« Reply #4 on: February 04, 2013, 08:40:39 PM »
Did you forget to clamp the hole with your thumb ?
Logged

Noahs Arc

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 1198
Re: Ghost shrimp pump problems
« Reply #5 on: February 04, 2013, 09:09:35 PM »
Soak the washer in fresh water overnight. Take a pair of pliers with you to the beach because I find it takes about 10-15 holes to get the sweet spot. Also make sure you back the nut off completely and hose it out when you get home.
Hope this helps
Logged

vancook

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 687
Re: Ghost shrimp pump problems
« Reply #6 on: February 04, 2013, 09:24:50 PM »
Quote from: Fish Assassin on February 04, 2013, 08:40:39 PM
Did you forget to clamp the hole with your thumb ?
I remembered to clamp the hole with my thumb.
Quote from: chris gadsden on February 04, 2013, 08:09:00 PM
Rubber washer most likely dried out, soak in some water for a few hours and see if that helps.
I will give this a try. Thanks for the tip Chris
Logged

Fish Assassin

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 10839
Re: Ghost shrimp pump problems
« Reply #7 on: February 04, 2013, 09:36:00 PM »
It's probably your washer. If soaking the washer don't work, you may need replacement washer. Berry's carries them.
Logged

vancook

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 687
Re: Ghost shrimp pump problems
« Reply #8 on: February 05, 2013, 04:50:05 PM »
Quote from: Fish Assassin on February 04, 2013, 09:36:00 PM
It's probably your washer. If soaking the washer don't work, you may need replacement washer. Berry's carries them.
Thanks for the info. Hopefully the soaking does the trick. Will be giving it another try in a few days
Logged

chironomidking

  • Full Member
  • ***
  • Offline Offline
  • Posts: 76
Re: Ghost shrimp pump problems
« Reply #9 on: February 07, 2013, 11:02:47 AM »
Buy a 2" Test Plug and replace the factory rubber washer system.  Just re-use the steel washer from the orginal setup and you're good to go.  I was able to pick up a Test Plug and Rona.

http://www.sears.com/shc/s/p_10153_12605_SPM6881299213P
Logged

vancook

  • Old Timer
  • *****
  • Offline Offline
  • Posts: 687
Re: Ghost shrimp pump problems
« Reply #10 on: February 07, 2013, 12:30:38 PM »
Quote from: chironomidking on February 07, 2013, 11:02:47 AM
Buy a 2" Test Plug and replace the factory rubber washer system.  Just re-use the steel washer from the orginal setup and you're good to go.  I was able to pick up a Test Plug and Rona.

http://www.sears.com/shc/s/p_10153_12605_SPM6881299213P

Thnks for the link. Not a bad idea to pick one up as a back up.
Going pumping tonight with the rehydrated seal. We'll see what happens
Logged